Edge-lighting PSB-60W-12VDC, 60 Watt 12 Volt DC Power Supply User Manual download pdf

PSB-60-12VDC

Installation Instructions for 60 Watt 12 Volt DC LED Power Supply

904-PSB-60-12VDC-01

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: 773-770-1195

Fax: 773-935-5613

www.edgelighting.com

[email protected]

SAVE THESE INSTRUCTIONS!

- Do not install this power supply in a wet location.

- To reduce the risk of the system overheating and possibly

causing a fire, make sure all the connections are tight.

- Do not install *LED fixture closer than three inches or as

specified in the *LED fixture installation instructions to

curtains or similarly combustible materials. Keep insulation

at least 3" away from the enclosure.

- Turn the electrical power off before modifying the lighting

system in any way.

- The system is "ETL" listed for USA and Canada only when

all the products used are supplied by Edge Lighting.

* See LED fixture installation instructions for proper

placement.

- RISK OF FIRE: This product must be installed by a

qualified electrician. Turn the power to the electrical box off

during installation. Read the "Important Safety Instructions "

before installation.

- This product is not suitable for wet locations. It is approved

for the use at any height above the finished floor.

- A typical installation is shown. Specific installation must be

in accordance with the local electrical codes.

- TO REDUCE RISK OF FIRE, it is important to wire the

power supply for the system as described in this

installation instruction.

- Load the power supply to MAXIMUM 60 Watts.

- Use Lightolier "ZP600FAM120" 0-10 volt controller to dim

the Warm White LED soft strip.

- Use CDP color dial or CTP color touch screen controller with

RGB LED soft strip.

GENERAL INFORMATION IMPORTANT SAFETY INSTRUCTIONS

LOW VOLTAGE WIRE SIZE CHART

POWER SUPPLY

WATTAGE

WIRE SIZE

UP TO 13 FT

WIRE SIZE

FOR 14-20 FT

WIRE SIZE

FOR 21-34 FT

WIRE SIZE

FOR 35-52 FT

60 WATT

12 Volt

#14 GA #12 GA #10 GA #8 GA

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - SAVE THESE INSTRUCTIONS!

PSB-60-12VDCInstallation Instructions for 60 Watt 12 Volt DC LED Power Supply 1904-PSB-60-12VDC-011718 W. Fullerton AveChicago, IL 60614Tel: 773-770-1

Page 2 - Soft Strip (Non-Dimmable)

Using LED Power Supply with a Light Switch & Warm White Soft Strip (Non-Dimmable)1 remove the cover.: Loosen the six Phillips screws on front o

Page 3 - Volt Dimmer

3Using LED Power Supply with Warm White Soft Strip & 0-10 Volt Dimmer SELV10-24 V=1-10V=0.6 mA<+-+-OUTPUTS TO LED MODULESINFCOVERPHILLIPS SCREW

Page 4 - POWER SUPPLY

SELV10-24 V=1-10V=0.6 mA<+-+-OUTPUTS TO LED MODULESINDIM MODULEPOWER SUPPLY4SELV10-24 V=1-10V=0.6 mA<+-+-OUTPUTS TO LED MODULESIN3DIM MODULEGELE

Page 5 - Controller

LED SOFT STRIPOUTPUTS TO LED MODULES161718212015: Use the "Low Voltage Wire Size Chart" on page 1 to determine the proper wire size co

Page 6

6MNELECTRICAL BOXCONDUIT98CONTROLLERCONTROLLERPOWER SUPPLYO10: Connect one end of a data wire (blue with white stripes wire) to controller "

Page 7 - L N G

7QM1718181717: Connect the yellow power supply wire marked "+" to DVR-RGB-60 "Vdc+" red terminal.18: Connect the black power

Page 8 - Wiring Diagrams

GROUND+24 VDCDATA +DATA -GROUND24VDC+ -LINEN LMExt in-Ext in+DMX in +DMX in -DMX in shieldLedSync thru+LedSync thru-LedSync shieldVDC+VDC-LED supply

Comments to this Manuals

No comments

Edge-lighting PSB-60W-12VDC, 60 Watt 12 Volt DC Power Supply User Manual

Browse online or download User Manual for Lighting Edge-lighting PSB-60W-12VDC, 60 Watt 12 Volt DC Power Supply. Edge Lighting PSB-60W-12VDC, 60 Watt 12 Volt DC Power Supply User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Edge-lighting PSB-60W-12VDC, 60 Watt 12 Volt DC Power Supply