Edge-lighting 2x250W/12V Surface Mount Magnetic Transformer User Manual download pdf

M2T-2X250-12-_

Installation Instructions for Monorail 2 Circuit 2 X 250

120 Volt Input to 12 Volt Single

Feed Output

Watt Surface

Mount Magnetic Transformer

904-M2T-2X250-12-04

1718 W. Fullerton Ave

Chicago, IL 60614

Tel: 773-770-1195

Fax: 773-935-5613

www.edgelighting.com

[email protected]

SAVE THESE INSTRUCTIONS!

- Do not install this lighting system in a damp or wet

location.

- Do not conceal or extend bus bar conductor through

building wall.

- To reduce the risk of fire and burns, do not install this

lighting system where the insulated open bus bar

conductors can be shorted or contact any conductive

materials.

- To reduce the risk of the system overheating and possibly

causing a fire, make sure all the connections are tight.

- Do not install fixture assemblies closer than six inches, or

as specified in the fixture installation instructions, to

curtains or similarly combustible materials.

- Turn the electrical power off before modifying the lighting

system in any way.

- The fixtures used with the Edge Lighting systems must be

identified for use with the corresponding Edge Lighting

systems.

- Minimum volume of the electrical box must be 6 cubic

inches (98 cubic centimeters).

- The system is "ETL" listed for USA and Canada only when

all the products used are supplied by Edge Lighting.

- RISK OF FIRE: This product must be installed by a

qualified electrician. Turn the power to the electrical box off

during installation. Read the "Important Safety Instructions"

before installation.

- This product is suitable only for indoor dry locations and

approved for the use at any height above the finished floor.

- This product contains a magnetic transformer with a built-in

dimming coil.

- This product may be dimmed only with a low voltage

magnetic dimmer. Using a dimmer other than specified may

work initially, but will eventually cause transformer failure

and void the warranty. The dimmer must be derated as

indicated by the dimmer manufacturer.

- A typical installation is shown. Specific installation must be

in accordance with the local electrical codes.

- Load each circuit of the surface mount transformer to

MAXIMUM 250 Watt.

GENERAL INFORMATION IMPORTANT SAFETY INSTRUCTIONS

1 2 3 4

Summary of Contents

Page 1 - Mount Magnetic Transformer

M2T-2X250-12-_Installation Instructions for Monorail 2 Circuit 2 X 250 120 Volt Input to 12 Volt Single Feed OutputWatt Surface Mount Magnetic Transfo

Page 2

COVER HOUSING SET SCREW 2Install the Surface Mount Transformer1: Loosen and remove the five M4 button head screws around the transformer cover wit

Page 3

13MONORAIL 2 CIRCUIT FEED CONTACT SET SCREW310: Feed the extension wires through the transformer housing center hole. Slide the transformer hous

Page 4

4Install the Monorail 2 Circuit Sections to the TransformerISTRAIGHTCONDUCTIVECONNECTOR1ONE MONORAIL 2 CIRCUIT SECTIONMONORAIL 2 CIRCUIT FEED CONTACTS

Edge-lighting 2x250W/12V Surface Mount Magnetic Transformer User Manual

Browse online or download User Manual for Lighting Edge-lighting 2x250W/12V Surface Mount Magnetic Transformer. Edge Lighting 2x250W/12V Surface Mount Magnetic Transformer User Manual

Summary of Contents

More documents for Lighting Edge-lighting 2x250W/12V Surface Mount Magnetic Transformer

Comments to this Manuals

Edge-lighting 2x250W/12V Surface Mount Magnetic Transformer User Manual

Browse online or download User Manual for Lighting Edge-lighting 2x250W/12V Surface Mount Magnetic Transformer. Edge Lighting 2x250W/12V Surface Mount Magnetic Transformer User Manual

Summary of Contents

More documents for Lighting Edge-lighting 2x250W/12V Surface Mount Magnetic Transformer

Comments to this Manuals

Related products and manuals for Lighting Edge-lighting 2x250W/12V Surface Mount Magnetic Transformer